# Drum Architect Live user guide

[Install](INSTALL.md) · [Quick start](QUICK_START.md) · [Release notes](RELEASE_NOTES.md)

## Scan and export

Live uses the recorded mix to plan grooves, breaks and fills. It supports straight 4/4 at a constant tempo. **Rock/Pop** and **Soul/Funk** are the two Drum Feel styles.

Press **SCAN AUDIO** before starting playback. Capture starts with DAW playback when the host reports transport, including leading silence. Without transport data, capture can start when audio arrives. If the host does not provide enough timing information, alignment may be approximate and fills may be limited. With an enabled sidechain, Live scans that input; otherwise it scans its main input.

Use **STOP CAPTURE** to finish and generate. **CANCEL SCAN** disarms the scan. **CANCEL** during generation clears the scan and its result. After **MIDI READY**, drag or save editable GM drum MIDI. The file uses channel 10. Match the start and tempo to the source and use a GM map in your drum instrument.

**REGENERATE MIDI** uses the last scan and advances the variant. Live reanalyzes the retained audio when analysis settings change. TIMING, FILL STYLE and active FILLS use the existing analysis. A new scan is needed for changed source audio, routing, tempo or capture start, or if the last scan is no longer available.

## Arrangement Intelligence

The result opens over the spectrum as soon as the first MIDI is ready. It shows the available section map, planned fill count, and the style and controls used for that MIDI. Low confidence is shown when reported by the analysis. Editing the knobs does not change this summary until you regenerate. Starting or cancelling a new scan clears the previous result.

## Controls

Controls run from **−10 to +10**. **0** is the default in a new instance. Change a control, then press **REGENERATE MIDI**.

| Control | What it changes |
|---|---|
| **SPACE — Sparser ↔ Fuller** | Sparser leaves more room. Fuller lets the groove continue through more audible sections. It does not fill silence. It also affects how the audio analysis finds breaks. |
| **RISE — Subtle ↔ Active** | Subtle uses fewer build and transition fill opportunities. Active allows more eligible approaches. It also affects build detection during analysis. |
| **IMPACT — Soft ↔ Hard** | Soft gives lighter hits. Hard gives stronger main hits and accents. It also affects drop detection during analysis. |
| **TIMING — Tight ↔ Loose** | Tight reduces small timing offsets. Loose adds push and pull while holding strong beats and fill landings steady. **0** keeps the original timing. Notes, velocities and the intended rhythm, including any planned swing, stay intact. This build generates straight 4/4 and does not add swing. |
| **FILL STYLE — Snare ↔ Kit** | Snare uses one snare sound. Kit spreads the same fill rhythm over the kit. **0** keeps the original voicing. Fill count, placement, timing, velocity and landing stay the same. Ordinary groove hits stay as they are. |
| **FILLS — Off ↔ More** | Sets how many eligible fills are used. More can add fills when there is room. **Off (−10)** overrides RISE and FILL STYLE. |

For example, a four-hit fill might be **snare–snare–snare–snare** at Snare and **snare–high tom–mid tom–floor tom** at Kit. Kit can use an occasional cymbal in a suitable fill. A fill can retain its original voicing if a change would make the same rhythm unplayable under the repetition limits.

**RISE and FILLS** influence where fills can occur and how many are used. **FILL STYLE** changes which parts of the kit play the selected fills. Some sections have no eligible fill points at any setting.

## Saved projects

Your DAW project saves the selected Drum Feel, control values, presets and which control responses are active. It does not save the scan, analysis, generated MIDI inside Live or the variant counter. Clips already dragged into the DAW are saved by the DAW; saved `.mid` files are separate.

New instances start with TIMING and FILL STYLE active at **0**. Older projects may show saved values without applying the current response. Move **TIMING** or **FILL STYLE** once to enable that knob in the project. Each activates independently. Earlier SPACE, RISE, IMPACT and FILLS responses may show **Low / High** until the current response is enabled. A legacy FILLS knob does not show **Off** until you move it to enable the current response. Opening or saving a project alone does not switch its response.

## Demo and license

The Live demo lasts **7 days** from the first use of the Live release on this Linux account and allows up to **1 minute per scan**. An active Live license allows up to **5 minutes per scan**. MIDI generation uses the same engine in both modes. For longer audio, scan in sections.

Open **Settings** to see your license status. Enter your **Drum Architect Live** key and choose **ACTIVATE LICENSE** while online. Live has its own demo and activation. A key for the original Drum Architect does not unlock Live, and a Live key does not unlock the original.

Existing Live customers can update without entering the key again. Live validates the saved activation with its existing ID. Both older Lemon Squeezy keys and newer Polar keys use the TrackTuner license service. Reinstalling on a clean account requires the same Live key and an available activation within your license limit.

Live checks its license automatically after 24 hours, including when its editor is closed. After a successful check, offline access lasts at most 14 days and can end earlier if the server specifies an earlier deadline or the license expires. A failed connection does not extend that deadline. Keep the saved activation and reconnect to recover access.

**REMOVE LICENSE FROM THIS COMPUTER** requests release of this computer. Wait for confirmation. If removal fails, the saved license stays in place; Settings shows the failure or retry delay. A pending activation requires support reconciliation. Do not repeatedly reinstall to work around it. Audio analysis and MIDI generation run locally; license activation and validation use the internet.

## Troubleshooting

| Problem | What to check |
|---|---|
| Live is missing from the plugin list | Verify the Linux x86_64 VST3 or CLAP plugin, scan path and DAW rescan. See [Install](INSTALL.md). |
| Scan stays armed or captures silence | Start DAW playback. Check signal at the plugin input and whether a sidechain is enabled. Try a clear section without looping or seeking. |
| A scan stops early | Check the demo or licensed time limit and sustained silence. Stop deliberately at the desired section end. |
| The groove is misaligned or fills are missing | Scan a constant-tempo 4/4 section from a known bar line. Check host timing, **FILLS OFF**, and whether there is an eligible transition. |
| The MIDI is silent or plays the wrong drums | Put it on a MIDI or instrument track with a drum instrument loaded. Check the GM map and channel routing. |
| A knob appears to have no effect | In an older project, move the knob to enable it. Press **REGENERATE MIDI**, then replace the clip. **FILL STYLE** has no effect if there are no fills. |
| Regenerate is unavailable after reopening | Scan again. The previous capture was temporary. |
| License cannot connect or activate | Check the network and key. If the key is rejected or the activation limit is reached, use the support information at [tracktuner.com](https://tracktuner.com/). |
